Product Shipping Box

Free next day delivery

…on all Owatrol orders placed before 3pm, working days only

Choose OptionBuy online & Save!
Qty:

Owatrol Oleofloor Classic

From £170.73

Interior Wood Floor Oil

Nourish your wooden floor from the inside and enhance the natural beauty of it.

Properties

  • Heavy traffic formula.
  • Pleasant odour.
  • Oleofloor Classic enhances the natural beauty of the wood.
  • Easy to apply.
  • Fast drying.
  • Excellent penetration – nourishes the wood.
  • Excellent resistance to abrasion and chemicals, including ammonia based products.
  • Water repellent.
  • Easy maintenance.
  • Does not require buffing or heavy and expensive application equipment.
  • Only first coat of Oleofloor Classic can be tinted with a universal colourant (max. 3%). Always try a sample first.

Where to use

  • Normal traffic: bedrooms, lounges, bathrooms etc
  • Heavy traffic: corridors, stairs, dining rooms, kitchen etc
  • All wooden floors, new and old including parquet flooring, veneered flooring and staircases.
  • Directly onto prepared wood.
  • Can be used on all soft and hardwoods including exotic hardwoods.

Surface Preparation

General Directions

  • Surfaces must be dry, clean, free of dirt, grease and other surface contamination including previous coatings.
  • Oleofloor Classic can only be applied to bare wood surfaces or a wood surface that was previously finished with Oleofloor Classic. All other finishes MUST be completely and thoroughly removed.
  • Always clean meticulously with a vacuum cleaner after each sanding, including any dust traps (skirting, radiators, pipes, window sills, etc).
  • Sand floor back to bare wood using an appropriate system and abrasive grades, depending on the condition of surface and wood species.
  • Cracks of 2 mm wide or less should be filled with Lianfloor and sanding resumed with 80 or 100 grit paper depending on the last grit used.
  • Finish with finishing grade up to grit No. 120 or 150 depending on the wood species and thickness of wear layer.

New Wood Surfaces

  • Degrease the surface with denatured alcohol, acetone or similar solvent based product.
  • Sand surface as instructed in “General Directions” above.

Previously Treated Surfaces (Oiled & Polished)

  • Previously oiled or polished surfaces should be dry stripped with DSP 800.
  • If, after stripping with DSP 800, the surface is in good condition and does not require sanding, neutralise with denatured alcohol, acetone, white (mineral) spirit or similar solvent based product before applying the finish.
  • If sanding is required, proceed as instructed in “General Directions”.

Previously Treated Surfaces (Paint, Stain, Varnish etc)

  • Remove existing finish by sanding or stripping with DSP 800.
  • If, after stripping with DSP 800, the surface is in good condition and does not require sanding, neutralise with denatured alcohol, acetone, white (mineral) spirit or similar solvent based product before applying the finish.
  • If sanding is required after stripping with DSP 800 or removal of finish is done by sanding, proceed as instructed in “General Directions”.

Application

  • Apply 1 or 2 coats of Oleofloor Classic depending on the type of wood and foot traffic.
  • Facing the light and starting opposite the door so as to work towards it, apply a first even and a generous coat of Oleofloor Classic.
  • Start at the edge then do the entire surface, working in areas of 2 m by 2 m.
  • Allow to dry for 4 hours depending on the ambient conditions.
  • Apply 2nd coat if required.
  • Do not leave more than 12 hours between application of the 1st and 2nd coat.
  • Always maintain a wet edge to avoid overlaps.

Information

Coverage: 15-20 m²/l per coat
Application tools:  Synthetic roller. Synthetic brush. Floor applicator pad – synthetic/microfibre. 
Application temperature: Between 10°C and 25°C.
Drying: Touch dry 1 – 2 hours, normal use – 24 hours.
Clean-up: Soap and water.